ROP-chain-generator for Wii U PowerPC-userland exploits.
This fork is supposed to be a common base for Wii U ROP-chains.
This is a common codebase for generating ROP-chains/etc for seperate Wii U PowerPC-userland exploits. This uses addresses auto-located from coreinit, with .php for each sysver that was pre-generated. This is basically a Wii U version of 3ds_browserhax_common.
Currently only binary ROP-chains are supported, hence no support for using this easily with WebKit exploits. The core1-switch ROP here doesn't work correctly currently, hence this codebase isn't usable as-is unless the current core is already core1(which isn't the case for WebKit exploits it seems). In other words, this codebase is currently only usable with non-WebKit exploits. Hence the use of php, this is intended for running under browser-based titles, but could be used with others as well if the ROP-chain(s) are usable with them.
You must specify the "sysver={val}" URL parameter for pages using this codebase, for selecting your Wii U system-version:
- "532": 5.3.2
- "540": 5.4.0
- "550": 5.5.0 / 5.5.1
Usage
This codebase uses config/etc names from the 3ds repo mentioned above.
If the exploit .php has to select a sysver without using the value selected with via the URL param, that could be done with the following for example(prior to using the require_once() for the common .php): "$sysver = 550;" DO NOT set $sysver to any data directly specified by the user.
The $ropchainselect field determines which ROP-chain to use. Only one ROP-chain is implemented currently. When this param isn't specified, the codebase will select the default ROP-chain(val1).
The default ROP-chain does the following(only usable with titles which have codegen access):
- Runs the core1-switch ROP(see above).
- Loads the codebin payload into the codegen/JIT area(with the required OSSwitchSecCodeGenMode() calls before/after), and does dcache/icache flushing/invalidation.
- Pops addresses into registers which the codebin could then use, see source.
- Jumps to the codebin payload.
- See source.
The memory address of the codebin payload is required, see below. If the payload isn't guaranteed to always be at the exact same address all the time, storing a PowerPC NOP-sled right before the payload in memory is highly recommended(big-endian word value 0x60000000). The output of wiiuhaxx_generatepayload() is: wiiuhaxx_loader followed by the actual payload, with 4-byte alignment for the total size(see below).
Also note that this codebase itself does not need the address where the initial ROP-chain is located at all.
Example that the exploit .php can use:
<?php ... require_once("wiiu_browserhax_common.php"); ... $generatebinrop = 1; $payload_srcaddr = <address of payload codebin>; $ROPHEAP = <some valid address the ROP can use for storing tmp data>;//Such as the following: $payload_srcaddr-0x1000. generate_ropchain(); ... $payload = wiiuhaxx_generatepayload();//Binary codebin, include this in the output exploit so that it lands in memory usable by the ROP. if($payload === FALSE) { header("HTTP/1.1 500 Internal Server Error"); die("The payload binary doesn't exist / is invalid.\n"); } ... else if($i<{targetoffset}) { $writeval = $ROP_POPJUMPLR_STACK12;//ROP NOP-sled. } else if($i=={targetoffset}) { $con.= pack("N*", $ROP_POPJUMPLR_STACK12); $con.= pack("N*", 0x48484848);//If LR ever gets loaded from here there's no known way to recover from that automatically, this code would need manually adjusted if that ever happens. $i+= 0x8; $con.= $ROPCHAIN; $i+= strlen($ROPCHAIN)-4; //Verify that the $ROPCHAIN isn't too large somewhere in here. continue; } ... ?>
A config file located at "wiiuhaxx_common_cfg.php" is also required.
- $wiiuhaxxcfg_payloadfilepath is the filepath for the actual codebin payload to run, this will be loaded to codegen+0.
- $wiiuhaxxcfg_loaderfilepath is the filepath for wiiuhaxx_loader.bin. This loads the above payload, since due to the NOP-sled the initial code which runs(wiiuhaxx_loader) won't (always) land at codegen+0. This can be built by running the following: "make OUTPATH={directorypath/filepath to copy the .bin to}".
For example:
<?php $wiiuhaxxcfg_payloadfilepath = "<filepath for actual payload, such as wiiuhax_payload.bin, or for example: {projectdir}/bin/code550.bin>";//Remember that this is just an example, you can programmatically select the payload path by checking the request URL/etc if you want as well. $wiiuhaxxcfg_loaderfilepath = "<filepath for wiiuhaxx_loader.bin>"; $wiiuhaxxcfg_searchpayloadfilepath = "<filepath for wiiuhaxx_searcher.bin>"; ?>